How To Remove A Vinyl Fence Post

Download Article

Download Commodity

Vinyl fences are very resilient, so they don't require a lot of maintenance. If some role does break, your debate is also like shooting fish in a barrel to take apart and reassemble. The well-nigh difficult job is finding an identical replacement piece. One time you lot accept information technology, you tin speedily connect information technology to the existing parts. Your repaired fence can then serve as a feature of your domicile for many years.

Things You lot Should Know

• If a panel breaks on your vinyl fence, simply remove the top rail and panel from the section you want to replace, slide the new panels into place, and replace the track.
• You can too supervene upon the runway by cutting it to length, removing the damaged rails, and sliding the new rails into the holes on the fence post.
• If 1 of the posts gets damaged, unscrew the top rail, dig upward the damaged post, fix the new postal service in place with physical, and reattach the rails and panels.

1. 1

   Order similar replacement panels. You tin search online to observe many different fence styles. If you can, contact the fence's manufacturer to get new panels identical to the old ones. Take a moving-picture show of your fence and send it to companies to ensure yous get the right panels.^[1]

   • Try to get replacement parts that are the same size and look as close as possible to the rest of your debate.
   • Abode improvement stores may besides sell fence parts and repair kits.

2. ii

   Unscrew the top rail at the ends. The peak rail attaches to the closest posts. Wait for a pair of screws at the ends, securing the rails to those posts. Plough the screws counterclockwise to remove them, and then ready them bated.^[two]

   • These screws may be underneath the caps on the posts. Gently lift them with a hammer and chisel if you tin can't remove them past hand.
   • Keep the screws in a condom spot, such as a airtight container, then they can be reused later.

   Advertisement

3. 3

   Remove the screws from the damaged panels. Now that the track is gratis, locate the screws on the panels. If your argue'south panels have pickets, or vertical bars, behind them, the screws may be at the console's ends. Plough them counterclockwise to remove them.^[three]

   • Not all fences take pickets or screws. Your argue'due south panels may be held in place with brackets, which you can slide the panels out of.

4. iv

   Slide the panels out of the fence. Lift the elevation runway off of the panel you need to supersede. Then, pull the panel upwardly to remove information technology. If you took off all of the screws earlier, the console should come off of the fence easily.^[four]

   • If the panel is next to a post, it may be attached with side brackets. Advisedly move the console to the side and out of the brackets.

5. 5

   Check the alignment of the posts with a level. Before installing the new panels, brand sure the argue posts are level. Hold a level against the side of each connecting mail service. If a post is positioned correctly, the level will be appear flat from top to bottom. Straighten the posts as needed.^[5]

   • If your posts are held in the ground with concrete, they most likely will not need to exist adjusted.

6. 6

   Slide the new panels into the argue. Fit each console over the bottom rail. Adjust the panels carefully so each is level from superlative to bottom. Slide them into any nearby brackets, then identify the superlative rail over them. Brand sure each panel looks evenly spaced in the fence.^[6]

   • In most fences, the panels volition fit right next to each other without leaving a gap.

7. 7

   Screw the panels and summit rail in place. Look for the screw holes in the top and lesser ends of each console. Use these to fasten the panels to the stabilizing pickets, if your fence has them. Cease adjusting the height rail, then tighten the screws near the fence posts to secure information technology in identify.^[7]

   • If the spiral holes practice not line upward, you lot tin fill the existing panel holes with spray cream, so drill new holes one in (2.5 cm) deep.

Advertizing

1. 1

   Remove the panels from the track. If your argue'southward panels spike to pickets, remove the screws at the peak and bottom of the panels starting time. So, slide the panels out of the rails. Clear the rails completely.^[8]

2. two

   Unscrew the rail from the posts. Each rails slides into holes on the posts. You will observe a pair of screws holding the rails in position. Plow these counterclockwise and set them bated. So, slide the rails off of the posts.^[9]

   • Store the screws in a condom location and keep the old rails in case y'all demand to measure them.

3. three

   Measure the length of rails you need. You tin do this past running tape measure out from 1 post to another. Remember that each rail needs to have a little extra length in order to slide into the postal service holes. Add about 2 in (five.1 cm) onto the length.^[x]

   • If y'all have the old rail, you tin also measure out information technology for use every bit an estimate.

4. 4

   Habiliment safety goggles and other protective gear. Earlier sawing into the rails, take the proper safety precautions. Shield your optics from debris by wearing condom goggles. Embrace your mouth by wearing a respirator.

   • Avoid wearing loose clothing or jewelry when operating a saw.

5. five

   Cut the rail to length with a circular saw. Set the new track on a workbench. Earlier cut, mark where you demand to make the cuts and then you go the size of rails yous need. Then, advisedly cut through the rail.^[11]

   • For the all-time results, choose a saw blade labeled for vinyl cutting. Fence companies and dwelling improvement stores may sell these blades.

6. vi

   Slide the rail into the holes on the contend posts. Make sure the brackets for the panels are on the meridian side. Button the rail into the mail holes until the rail hangs in place. As long equally the rail is the right length, it should fit.^[12]

   • If the rail doesn't fit properly, check the length again. You may need to cut information technology a footling shorter.

7. 7

   Screw the rail to the posts. Locate the screw holes on either end of the rails. You will need a pair of screws on each side. Twist them clockwise to lock the rails in identify. When yous're done, you tin begin installing the vinyl panels.^[13]

   • The size of screws y'all need differ from rail to track.
   • Screws are normally included with new rails, just you tin endeavour using the screws from the old rail.

Ad

1. one

   Unscrew the connecting rails. Each track slides into slots on the post and is held in place with screws. Turn the screws counterclockwise to remove them. Pull both the top and bottom runway abroad from the postal service.^[14]

   • If you have trouble installing a post, removing the rail and argue panels completely can give you lot more space.

2. two

   Dig out the damaged postal service. Remove the old mail also equally whatever fragments that may be in the ground. If your post was held in place with concrete, you will need to dig up the physical to remove it.^[15]

   • To remove the concrete, dig out the dirt around it. You can refill the pigsty later.

3. 3

   Measure where the new postal service will be placed. To figure out where to place the new post, measure the distance betwixt two existing posts. The new mail should be placed an equal altitude from the last post. Marker the location with paint, tape, or some other indicator.^[xvi]

   • The post needs to be even and straight or else the rails and panels will non fit correctly.

4. 4

   Dig a hole 3 ft (0.91 m) deep in the ground. Dig out the spot yous marked earlier. Brand the pigsty about 8 in (twenty cm) in diameter. You can use a record measure to ensure the pigsty is the size you demand.

5. five

   Seal the pole in place with concrete. You will need about 120 lb (54 kg) of premixed concrete for ane mail. Place the mail service in the hole. While someone holds the post in position, fill the the hole with concrete. Pour the concrete until it is nigh 4 in (10 cm) below the ground's surface.^[17]

   • The other person should agree the mail service direct. If it doesn't look right, adjust information technology quickly before the physical solidifies.

6. half dozen

   Reinstall the argue rails and panels. Fit the contend rails into the holes on the new post, then brainstorm sliding the panels onto the rail. Screw the track to the within of the post. Then, attach the panels, screwing them in place if they likewise employ screws.^[18]

Advertisement

Add New Question

• Question

  How tin I repair a interruption in i of the panels on my fence?

  

  Ryaan Tuttle is a Dwelling Improvement Specialist and the CEO of All-time Handyman Boston. With over 15 years of experience, Ryaan specializes in dwelling comeback and holding maintenance past leveraging technology and adroitness. Ryaan holds his Construction Supervisor and Habitation Improvement Contractor Licenses. Different well-nigh handyman contractors, All-time Handyman Boston is licensed and insured. Boston Magazine and LocalBest.com have named Best Handyman Boston the Best Handyman in Boston.

  

  Domicile Improvement Specialist

  Expert Answer

  You actually would want to try to remove whatsoever panel that is. Whatever repair that you would make to it would be temporary, and it would but intermission again over time. Y'all could effort gluing it, but really information technology should be replaced if possible.

Ask a Question

200 characters left

Include your e-mail accost to get a message when this question is answered.

Submit

Ad

• Proceed whatsoever extra panels yous accept after installing your debate.

• There are many dissimilar vinyl debate styles, so finding the right parts can take some time and patience.

• Take a film of your fence then yous can get the right replacement parts.

Show More than Tips

Advertisement

Things You lot'll Need

• Replacement panels
• Screwdriver

• Replacement rail
• Screwdriver
• Measuring record
• Safety goggles
• Respirator
• Circular saw

• Replacement mail service
• Screwdriver
• Shovel
• Cement
• H2o
• Mixing container
• Measuring tape

About This Commodity

Thanks to all authors for creating a page that has been read 29,830 times.

Did this article help you?

Source: https://www.wikihow.com/Repair-a-Vinyl-Fence

Share this post